• Skip to primary navigation
  • Skip to main content
  • Skip to primary sidebar
  • Skip to footer
EMAIL 1-866-553-0373 CONTACT
CSM Metal Deck

CSM Metal Deck

Low Cost. Same Day Shipping. In-stock. Manufactured to Spec.

  • Roof Deck
  • Composite Deck
  • Form Deck
  • News
  • About
  • Contact

3” Composite Deck

3.0 VLI, CFD3, 3W Composite, 3" Lok-Floor, W3 Formlok

Get a Quote
Composite 3 inch deck

3” Composite Deck

3″ Composite Deck: Sturdy Floor Decking

In Stock – Fast Shipping or Same Day Pickup

We offer quality floor decking at competitive prices. 3″ Composite Metal Deck is a sturdy and easy to install choice for your metal floor decking.

CSM Metal Deck stocks and manufactures 3″ Composite Deck in 22, 20, 18, and 16 gauge. Typically 3″ Composite Deck is used for applications in outdoor flooring. CSM Metal Deck’s 3″ Composite Deck supports construction spans from 1 foot to 11 feet in distance, depending upon the gauge and back-span condition (single, double, triple).

We ship nationwide from our Houston, TX metal deck warehouse. Please complete the quote form below or call us at 1-866-553-0373 to request a custom quote for your construction project.

Engineering

Download as PDF

3 inch composite deck engineering properties

Get a Quote Download as PDF

Attachments

Download as PDF

3″ Composite Deck 24-3 Pattern

3 inch composite deck attachment

Notes: The following CSM Products & Solutions standard attachment pattern has been provided as a minimum recommendation for the product specified. The anchorage system of roof deck units to supporting members consists of Deck to Support, Deck to Deck (Sidelap) and Deck to Perimeter. When project specifications, specific design loads, or local building codes require more stringent patterns than those on our standard details, then the more restrictive requirements shall govern. The project Engineer of Record should review the standard requirements in order to verify conformance with project specifications, design loads, and local building code requirements. For additional information or attachment pattern configuration contact us.

The attachment patterns stated are applicable for use with various fastener types. Typical fastener types include arc puddle welds, screws and pins. Please refer to diaphragm shear capacity tables and uplift capacity tables for the product specified to confirm strength characteristics of the specified fastener type and attachment pattern.

CSM Products & Solutions recommends the use of weld washers for support attachments with deck units less than .028” (0.71 mm) thick (not required for 22 gauge). Shear studs on composite floor decks can be used to replace welds at supports. Due to the difficulty of side lap welding on 22 gauge and lighter metal decks, CSM Products & Solutions recommends these thicknesses be attached with side lap screws.

Get a Quote Download as PDF

Properties

Download as PDF

3″ Composite Deck

3 inch composite deck properties

Get a Quote Download as PDF

Installation

Download as PDF

Floor Deck Installation

CSM steel composite floor deck panels and accessories shall be installed by qualified and experienced workers. Floor deck and accessories shall be placed in accordance with approved erection drawings. Maintaining rib alignment across the structure is very important to achieve continuous concrete ribs across abutting sheet ends. A snap chalk line shall be used at reasonable intervals to assure proper alignment and accurate coverage of deck panels.

Position the first sheet as noted on the erection drawings with the upstanding leg the leading or open edge. When one row is placed, begin another, making alignment adjustments as necessary. Do not use unfastened deck as a working platform or storage area.

All sheets are furnished with square ends and full width. Partial width sheets as well as skew cuts shall be field cut by the deck erector to fit field conditions. All accessories, i.e. pour stops, side closures and end closures are manufactured in standard stock lengths. Cutting and fitting of accessories when furnished is by the deck erector. Openings not shown on the erection drawings such as those required for stack, conduits, plumbing, vents, etc. shall be cut (and reinforced if necessary) by the trades requiring the openings.

Integral hanger tabs are rolled in when required. The maximum loading per tab is 100 lb. The deck erector must flatten out all tabs that interfere with proper bearing of deck on supporting steel. Hanger tabs are spaced nominally 12″ on center each way. Hanger tabs occur in a repetitive pattern that cannot be maintained across deck joints and cannot be located at predetermined locations. It is imperative that the load carried by the tabs is designed in such a way that the design load is not exceeded on any one tab.

Attachment

Floor deck sheets and accessories shall be attached as soon as possible and all sheets and accessories shall be attached at the end of each working day. Electric arc welding is the best and most economical method for attaching composite deck sheets to structural supports. Welder shall follow close to the placement crew.

All welds are to be made from the top of the deck down through the bottom flange of the ribs. Welds shall penetrate and attach all thickness of material to the structural supports. Care shall be exercised on the selection of the electrodes to provide positive attachment and to prevent high amperage blow holes.

Deck panels are to be fastened to all supports at 12″ on center maximum with not less than 3/4″ diameter arc spot welds. At deck butt joints, both sheets are to be fastened. Deck panels with spans greater than 5 feet shall have side laps and perimeter edges (at perimeter supports) fastened at mid-span or 36″ intervals – whichever is smaller.

1-1/2″ deep deck side laps are to be screw attached or welded.

2″ and 3″ deep deck side laps are to be button punched, welded or Gator Crimp (GTR).

End closures of the deck (if required) are to be fastened by tack welding or sheet metal screws at 36″ centers maximum.

Side closures of the deck (if required) are to be fastened by 1″ fillet welds at 12″ centers maximum.

Pour stop accessories of the deck (if required) are to be fastened by 1″ fillet welds at 12″ centers maximum.

Site Storage

Deck not promptly erected shall be stored off the ground with one end elevated and protected from the elements with a tarpaulin or other weatherproof covering, ventilated to avoid condensation. Reference SDI Manual of Construction Site Storage and Protection.

Protective Coating

All steel to be used in CSM steel composite floor deck shall be galvanized or phosphatized top and prime painted bottom. The paint coating is considered only a primer and shall be considered an impermanent and provisional coating. Galvanized finish in G-60 or G-90 coating is desirable in high moisture atmospheric conditions.

CSM shall not be responsible for the cleaning of the underside of steel floor deck to ensure bond of the sprayed-on fireproofing. Adherence of fireproofing is dependent on many variables. The adhesion or adherence of fireproofing products is the responsibility of the fireproofing applicator and fireproofing manufacturer.

Construction Loading

Do not use unfastened deck as a work or storage platform. Caution must be used with construction loading so that deck capacity is not exceeded and the deck is not damaged. When placing concrete, care must be exercised so that the deck will not be subject to impact that exceeds the design capacity of the deck. Concrete shall be placed from a low level in a uniform manner over the supporting structure and spread toward the center of the deck span.

Do not use chloride admixtures or admixtures containing chloride salts in concrete poured on composite deck. Such additives have proven deleterious to steel and steel finish.

Get a Quote Download as PDF

Construction Details

Download as PDF

Butt Deck

composite deck butt deck illustration

End Closure with Pour Stop or Bent Plate

composite deck end closure illustration

Pour Stop and End Closure

composite deck pour stop illustration

End Closure

composite deck end closure illustration

Pour Stop or Bent Plate

composite deck pour or bent plate illustration

Gage Closure

composite deck gage closure illustration

Zee Closure

composite deck zee closure illustration

Composite Deck

composite deck illustration

Get a Quote Download as PDF

Get a Quote

  • For finish other than Galvanized, state your preference in the “Special Requests” field below
  • Quote purpose

  • Delivery information

  • Date Format: MM slash DD slash YYYY
  • Send quote to

  • This field is for validation purposes and should be left unchanged.

Primary Sidebar

About CSM Metal Deck

At CSM we know metal deck. We have been supplying metal deck throughout the country for over 50 years. Choose from metal roof deck, composite deck and form deck, in a variety of depths, widths and gauges.

  • This field is for validation purposes and should be left unchanged.

Recent Articles

  • Is Painted Roof Deck Right for My Project?
  • Metal Roof Deck vs. Floor Deck
  • Ways to Attach Metal Deck

Footer

CSM Metal Deck

8660 Lambright Road
Houston, TX 77075
1-866-553-0373
info@metaldecking.com

  • Privacy Policy

Copyright © 2021 CSM Products and Solutions, LLC